Harz Labs Dental Sand A1-A2 / A3 3D Printing resin


3D Printing resin Harz Labs Dental Sand A1-A2 and A3, designed for dental demonstration models of crowns and bridges. Very tough, non-irritant, odorless resin with color A1-A2 and A3 according to Vita scale. Compatible with DLP and LCD 3D printers. SLA 3D printers version available upon request.



Dental Sand A1-A2 and A3 3D printing resin is PMMA-like micro filled composite resin, made of biocompatible raw materials, with color close to A1-A2-A3 according to Vita scale.

It has high hardness, 90 Shore D, and high tensile strength, stable to mechanical stress and chemicals

Recommended for printing of temporary crowns and bridges. Low odor and absence of harmful monomers allows to print in the laboratory with no need for special equipment.

Russian certification. Product without european certification, to be used only for models.



3D printing settings on most widespread 3D printers

click here

Harz Labs Dental Sand 3D printing resin in A1-A2 and A3 colors in the version for SLA 3D printers, such as Form1 / 2 and Peopoly, is available upon request. Write to us at: info@3dsolutions.store.

3D printing resin Harz Labs Dental Sand A1 A2 characteristics

 Package                 1kg/0.5kg
 Applications    Dental models
 Color    Opaque, Beige
 Viscosity (Brookfield)       at 25°C      1,2-1,5 Pa.s
 Hardness (Shore D)    90-92
 Tensile strenght    60 N/mm2
 Elongation at break    3-4%%
 Shrinkage    <0.5%




    Very high hardness, tensile strength, abrasion and scratch resistance due to ceramic fillers.


    Resins are odorless and cause no irritation, so you can work with natural ventilation without specialequipment.


    Depending on postcuring A1 or A2 color is achievable. It is stable for long time even in contact with aggressive agents.


    Produced from bio-compatible raw material used in photopolymer teeth fillings. Meets standards ISO 10993. 


    Resin is stable to solvents, aggressive inorganic agents like acid and alkalis.


    Pigments and fillers are well stabilized, no sedimentation and flocculation occur, no foam appears.

Correct post-processing process for temporaries

  1. To remove excess resin, wash the 3D printed part in an ultrasonic bath with the TEK1960 * solvent cleaner for 2 cycles of 2-3 minutes.

  2. Do not soak in acetone. Do not leave the 3D part soaking in the liquid. Use a soft brush if necessary.

  3. Dry with compressed air.

  4. Heat for 10-20 min in oven at 60 * C

  5. Perform post-curing in a oven with turntable and 36-48 W UV LED lamps for 30-60 minutes

  6. Polish and apply protective varnish (eg Optiglaze)

*We do not recommend the use of denatured or isopropyl alcohol (IPA). It is very aggressive on the polymerized resin and it could weaken the structure of the 3D part. It is also flammable and potentially harmful to people and the environment.

Store the resin in a dry, cool, shaded place out of direct sunlight.

Safety notice

The company I.D.M di Marin Davide is not a manufacturer of medical materials or devices. The material sold on this site is neither produced nor controlled by the company I.D.M. di Marin Davide, who in no case can be held responsible for any damage caused by use or application of the material, which must only be used on suitable machines and by specialized personnel, exclusively for the purpose indicated, according to the manufacturer’s instructions. For resins with European certification, the properties of the finished product vary according to the entire printing and post-curing process; refer to the manufacturer for any information about it.


 More Information                     MSDS

Additional information

Weight 1.5 kg
Dimensions 10 × 10 × 30 cm

1 KG, 0,5 KG


A1-A2, A3


There are no reviews yet.

Be the first to review “Harz Labs Dental Sand A1-A2 / A3 3D Printing resin”

Your email address will not be published. Required fields are marked *

Slide to unlock *

This site uses Akismet to reduce spam. Learn how your comment data is processed.