Harz Labs Dental Peach 3D Printing Resin

Description

Dental Peach photopolymer is a matte resin made from biocompatible raw materials. Available colors: Peach (available for Form2), Beige,Bone. It has a high Shore D hardness and high tensile strength, resistant to mechanical and thermal influences. The weakly expressed smell and the absence of harmful monomers allows you to work with it even in a small laboratory. Certified for medical use. Registration certificate for a medical device No. RZN 2020/12007.

 

Russian certification. Product without European certification, to be used only for models.

COMPATIBLE WITH MAIN DLP/LCD 3D PRINTERS

 

3D printing settings on most widespread 3D printers

click here

 

Harzl Labs Dental Peach 3D printing resin in the version for SLA 3D printers, such as Form1 / 2 and Peopoly, is available upon request. Write to us at: info@3dsolutions.store.

 

3D printing resin Harz Labs Dental Peach characteristics

 

Appearance		Opaque liquid
Color		Peach
Odor		Weak odor
Viscosity (Brookfield)	at 25°C	575 ± 225 mPa·s
Hardness (Shore D)		79.0 ± 2.0
Tensile strength		45.2 ± 4.4 MPa
Elongation at break		7.1 ± 3.1%
Shrinkage		<0.5%

 

Advantages

 

• SAFE

  Resin does not contain solvents and volatile monomers, irritating compounds. No fumes, odor and allergic reaction. Сan be used in lab or even at home.

• ACCURATE

  Provides high precision printing.

• HEAT RESISTANT

  Models has long-term stability under 100°. Also has short-term stability up to 180°C and can be used for films thermosettling.

• CERTIFICATION

  Biocompatibility was confirmed by the third-party laboratories. Material was successfully tested in accordance with ISO 10993 with the provision of the MA No. RZN 2020/12007.

• LOW SHRINKAGE

  Shrinkage less than 0.5% gives you the same size of the 3D model on your computer.

• BIOCOMPATIBLE

  Produced from biocompatible raw material used in photopolymer teeth fillings. Meets the standards ISO 10993. 

• DURABLE

  Pigments and fillers are well stabilized, no sedimentation and flocculation occur and no foam appears.

Finishing Instructions

1. Agitate in a vat with TEK1960* solvent for 1-2 minutes to remove excess resin.

2. Do not soak in acetone. Do not leave the 3D part soaking in the liquid. Use a soft brush if necessary.

3. Clean off any excess of liquid with a cold blowdryer or compressed air.

4. Leave under the sun or in a UV lamp to cure. The resin is fully cured when fingernails do not leave scratch marks on the object.

*We do not recommend the use of denatured or isopropyl alcohol (IPA). It is very aggressive on the polymerized resin and it could weaken the structure of the 3D part. It is also flammable and potentially harmful to people and the environment.

Store the resin in a dry, cool, shaded place out of direct sunlight.

Safety notice

The company I.D.M di Marin Davide is not a manufacturer of medical materials or devices. The material sold on this site is neither produced nor controlled by the company I.D.M. di Marin Davide, who in no case can be held responsible for any damage caused by use or application of the material, which must only be used on suitable machines and by specialized personnel, exclusively for the purpose indicated, according to the manufacturer’s instructions. For resins with European certification, the properties of the finished product vary according to the entire printing and post-curing process; refer to the manufacturer for any information about it.

 

 More Information                     MSDS